Filter By:

  • Show More Brands
  • Show Fewer Brands
  • Show More Sizes
  • Show Fewer Sizes

Accessories

Tifosi Veloce
$59.95
You'll look and ride fast in Tifosi's Veloce glasses. These stylish, lightweight specs boast Tifosi's exceptionally tough Grilamid frames and include three sets of easily interchangeable lenses, so you can see clearly in any light condition. Their open-frame design and large, impact-resistant, polycarbonate lenses offer a wide field of vision and protect you from debris, while the lens vents ensure fog-free vision. And, you'll love the hydrophilic rubber temples and nose pads that adjust in all directions and grip better when wet for a comfortable fit that stays put.
Thorn Cantilever Light Mount
$36.00
The Thorn cantilever mount eliminates the potential breakage problem that is particular to cantilever mounts. If your front brake yoke is high enough to clear the hole in the fork crown, this mount is unbeatable (and virtually unbreakable). Good stuff. See related items below if you need to lengthen your yoke cable.
Supernova New Handlebar Mount
$24.00
This mount adapts the Supernova E3 Pro 2 for handle bar mounting. It will also work on any light with a standard 10mm wide x 6mm bracket like the the Schmidt eDelux or lights from Busch & Müller. Two O-rings with different elasticity are included for use on bars or stems of 25.4mm-31.8mm.
Sunlite Classic Flower Basket
$10.95 - $11.95
Sunlite's Classic Flower Basket is just like the ones you remember as a kid. Made from weather-resistant plastic, it's tough, light and durable. It fits most handlebars and the flowers are removable. Carry your stuff in style.
Stages Cycling Shimano DXR MX71
$649.99
The BMX specific DXR MX71 Stages Power meter replaces a non-drive crank arm for existing Shimano DXR MX71 model cranks. Riders looking to add power to their existing crank need only select length — the Stages Power meter fits all current generation DXR cranksets. - Accuracy: ± 2% - Weight: Only adds 20 grams to base crank arm - Battery Life: 200+ hours (coin cell: CR2032) - Power range (Watts): 0 to 2500 - Cadence range (rpm): 20-220 - Water resistance rating: IPX7 - Frame Compatibility: Most frames, see fit guide in the Stages Support section - Crank Compatibility: Shimano Saint and DXR Hollowtech II cranks - Device Compatibility: ANT+, Bluetooth Smart Ready - Software Compatibiity: Training Peaks, Strava, Garmin Training Center and others
Sinewave Cycles Reactor Dynamo USB Charger
$220.00
Introducing the Sinewave Reactor! The performance of the Revolution dynamo-powered USB charger has been shrunk it into a package that fits above the star nut in a threadless steerer tube, with a pass through for the 6mm bolt. The only visible part is a custom CNC-milled stem cap holding the USB connector. The cap is only 10.6mm tall. Silver, black and red anodized finishes available. The Reactor is compatible with 1" and 1 1/8" threadless systems. Uses: Bicycle touring Commuting Green/Portable Electricity for USB Powered Devices Power USB Battery Chargers or External USB Power Packs Emergency Power Source Navigation while riding Music while riding Features: Best in class efficiency High Speed Overload Protection Fits 1" or 1 1/8" threadless steerers Light weight Waterproof Specifications: Starts charging at 3.5 MPH (5.5 km/h) Full charging at 9 MPH (14.4km/h) Warranty: 1 year on defects in materials and workmanship.
Sinewave Cycles Reactor Dynamo USB Charger RED
$169.95 $220.00 23% Savings
Introducing the Sinewave Reactor! The performance of the Revolution dynamo-powered USB charger has been shrunk it into a package that fits above the star nut in a threadless steerer tube, with a pass through for the 6mm bolt. The only visible part is a custom CNC-milled stem cap holding the USB connector. The cap is only 10.6mm tall. The Reactor is compatible with 1" and 1 1/8" threadless systems. Uses: Bicycle touring Commuting Green/Portable Electricity for USB Powered Devices Power USB Battery Chargers or External USB Power Packs Emergency Power Source Navigation while riding Music while riding Features: Best in class efficiency High Speed Overload Protection Fits 1" or 1 1/8" threadless steerers Light weight Waterproof Specifications: Starts charging at 3.5 MPH (5.5 km/h) Full charging at 9 MPH (14.4km/h) Warranty: 1 year on defects in materials and workmanship.
Sinewave Cycles Revolution Dynamo USB Charger
$120.00
1 to 3 Day Lead Time The Sinewave Cycles Revolution is a state-of-the-art dynamo powered USB charger. With it, you can charge your GPS device, iPhone, lap top, smart phone, tablet, backup battery lights, external battery pack or virtually any other USB device while riding. Uses: Bicycle touring Commuting Green/Portable Electricity for USB Powered Devices Power USB Battery Chargers or External USB Power Packs Emergency Power Source Navigation while riding Music while riding Features: Best in class efficiency High Speed Overload Protection Simple Installation Light weight Waterproof Specifications: Starts charging at 3.5 MPH (5.5 km/h) Full charging at 9 MPH (14.4km/h) Weight: 37 grams Dimensions: 14x35x54 mm Wire length: 36" (91 cm) (contact us if your setup requires a longer wire) Wire ends: Stripped wire Warranty: 1 year on defects in materials and workmanship.
Shimano Connector Plug for Nexus Generator (Dynamo)
$3.95
One of these plugs comes with each Shimano Nexus generator hub, but if you need extras, we have them. These also work well with Shutter Precision (SP) and Supernova dynamo hubs.
Serfas Thunderbolt Combo
$75.00
Lightning does strike twice with Serfas' CP-R4 combo pack. We've assembled our best selling lights into one package to bring you the best of both worlds. - 90 lumen headlight - 35 lumen tail light - USB rechargeable - Easily mounted to any bike - Removable straps allow endless mounting options - LED strip creates a non-directional flood of light - Runtime headlight: 1.5-9 hrs depending on setting - Runtime tail light: 9.5 hours max
Serfas Thunderbolt Taillight
$35.00
Serfas' Thunderbolt Taillight delivers 35 lumens in an extremely versatile, USB-rechargeable package. Attach the water-resistant silicone body nearly anywhere on your bike, and use the high, low, or two flash modes to make sure cars or cyclists can see you when approaching from behind after dark. At just 50 grams, you won't even notice it's on your bike — but others will!
Serfas TL-STN Seat Stay Taillight
$20.00
Be safe out there with Serfas' TL-STN Seat Stay Taillight. This water-resistant safety beacon will get you noticed out on the road with a large, super-bright 1/2-watt red LED flanked by 6 brilliant smaller LEDs. Plus, the weatherproof silicone body stretches to easily mount to any tube on your bike. Use a few Seat Stay Taillights for 360-degrees of visibility! This great light has steady, strobe and flash modes.
Schmidt Coaxial taillight wire 190cm
$14.00
Heavy duty coaxial wire for taillights. Coax is the most durable and attractive wire for this purpose. This is the same wire used as original wiring on Schmidt headlights. Available in two versions: The first photo shows the coax for Schmidt headlights. A circular ground connector and a 2.8mm female spade connector are installed on one end. This is the combination required for use with older Schmidt halogen Lumotec, Schmidt E6, Edelux/Edelux II headlights, which ground through the base. The lollipop ground connector gets installed on the mounting bolt at the base of the lamp. The power lead attaches to the connector in the base. Included are two loose 2.8mm female spade connectors for taillights. Many of the B&M taillights can be connected with bare wire, so they may not be necessary. The second photo shows the one for B&M headlights. It has two 2.8mm female spade connectors installed at one end. Also included are two loose 2.8mm female spade connectors for taillights if needed. 3mm O.D. x 190cm long.
Schmidt Handlebar mount
$43.00
Will securely and attractively support head lights from Busch & Müller, Schmidt, Supernova, and others on bars with a diameter from 22 to 31.8mm. Available in polished silver and black. So, what's not to like?
Schmidt Schmidt Edelux II Generator Headlight
$173.00 - $189.00
The new Edelux II "raises the bar" for dynamo headlights. The beam is wider, more even, and no longer is there a dark near field area (directly in front of the bike). The beam is asymmetric (like an automotive low beam) and concentrates the light on the road where it is needed most. Glare for oncoming riders and drivers is reduced. For added safety, a stand light glows for several minutes when the rider stops. The Edelux II has a three position switch (on/senso/off). In senso mode it will automatically come on in low light (like a tunnel or deep shadows) for safety. The glass lens has a non-glare coating for maximum efficiency and durability. The housing is completely sealed against moisture. Comes with necessary wiring for headlight only. Taillight wiring not included. See Related Items. Features include: -90 lux output - SUPER BRIGHT! -Standlight -On/Off and Senso mode (3 position switch) -Can be used with, or without, a tail light. -Aluminium casing and copper heat sink for efficient dissipation of heat from the LED. -Available in black anodized, silver anodized, polished aluminium, or red anodized. -Weight: 85g.
Schmidt Schmidt Upside Down Edelux II Generator Headlight
$201.00 - $216.00
Special Order: 1-3 day lead time The Edelux II "raises the bar" for dynamo headlights. The beam is wider, more even, and no longer is there a dark near field area (directly in front of the bike). The beam is asymmetric (like an automotive low beam) and concentrates the light on the road where it is needed most. Glare for oncoming riders and drivers is reduced. For added safety, a stand light glows for several minutes when the rider stops. There is no Senso mode as on the original right side up (non-inverted) model. The Upside Down (inverted) Edelux II is available in two versions. One has a two position switch (on/off) and a 140 cm wire with bare ends. The second model has no switch and is designed to be used with an external switch or run "always on" if wired directly. Rather than hard wired leads, it has connectors for wires running to it from the switch or dynamo. The glass lens has a non-glare coating for maximum efficiency and durability. The housing is completely sealed against moisture. We include loose 4.8mm spade connectors (for Schmidt hubs) at no charge or install them at a specified length for $12 (make a note in the comment field at checkout for this service). Features include:
  • 90 lux output - SUPER BRIGHT!
  • Standlight
  • Can be used with, or without, a tail light.
  • Aluminium casing and copper heat sink for efficient dissipation of heat from the LED.
  • Available in polished silver finish only.
  • Weight: 85g.
  • R & M R&M Handlebar Mount
    $23.00
    Allows the use of lights with standard 10mm mount tabs (Supernova, B&M, Schmidt, etc) lights on 22.2 - 26.0 handlebars. Concave washers provide capability for horizontal (left/right) as well as vertical (up/down) adjustment.
    Quad Lock iPhone Bike Mounting Kit
    $69.95
    The lightest, strongest and most secure iPhone mounting system on the market! -Kit is supplied with everything you need to mount to your bike -Composite case construction - tough polycarbonate core with durable TPU outer -Can be mounted on most bars and tubes ranging from 25 to 40mm diameter -Larger tubes diameters can also be used but may require longer zip ties (not included) -Clear "Poncho" cover helps keep phone dry and dirt-free
    Problem Solvers Sheldon Nut Fender Nut Set
    $16.00
    Also available w/32mm front nut for carbon forks Problem Solvers Sheldon Fender Nut Set. A set of recessed brake nuts for road brakes that has an extended threaded section for mounting fenders. Standard 6mm "recessed" brake nut with longer internal threading and extension on the back for a 6mm mounting bolt Install brake caliper normally, and mount fender to nut with a 6mm bolt Includes a 13mm front brake nut and a 10mm rear brake nut This pair of Fender Nuts should fit most steel and Aluminum road frames and forks. Make a note in the comment field at checkout if you want us to include the two M6 x 12 button head bolts needed to attach fenders to these nuts. They are not included in the packaging.
    Planet Bike Blinky 3 Taillight
    $13.95
    Make sure you have excellent rear visibility at night with the Blinky 3. This sweet taillight aims 3 bright LEDs directionally to provide visibility from up to a mile away. Its soft-touch power switch accesses flashing or steady modes for up to 100 hours of run time on the 2 AAA batteries (included). And, it includes seatpost and seatstay mounts.
    Planet Bike Eco Rack
    $29.99
    Planet Bike's Eco Rack is made of oversize tubular 6061-aluminum for maximum strength and stability. It's designed to provide complete heel clearance when you install packs. And, the pre-installed rack hardware makes it a cinch to mount the Eco Rack to your bike, too. This rack fits most road, mountain and hybrid bicycles and even includes a built-in platform, which doubles as a mini-fender on rainy rides.
    Planet Bike SuperFlash LED Red Tail Light for Bicycles
    $24.95
    Half-watt Blaze ® LED plus 2 eXtreme ® LEDs for visibility up to 1 mile -Unique, eye-catching flash pattern -Flashing and steady mode -Ultra compact vertical design is weatherproof, lightweight and durable -Includes bike mounts and clip mount for multiple mounting options -Up to 100 hours of run time on 2 AAA batteries (included)
    Planet Bike SuperFlash LED Red Tail Light USB Rechargeable
    $33.95
    One of our favorite tail lights - Now in a USB version! The ultra-compact case is weatherproof, light and durable, and features a soft-touch power switch. - Includes bike mounts and clip mount for multiple mounting options as well as USB charging cable -USB rechargeable lithium ion battery for 36 hours of runtime from a 2-4 hour charge -Low battery flash pattern indicates the remaining 20 minutes of battery life -Unique, eye-catching flash pattern -Flashing and steady mode
    Park Tool Micro Pump
    $17.95
    Park Tool's Micro Pump is a super small micro pump that fits in just about any bag or jersey pocket or mounts directly to the frame. Ideal to take along when space and weight are an issue. Aluminum barrel with a locking dual head and soft-touch dual-density flip out handle. - Presta and Schrader valve compatible - Maximum pressure: 100 psi / 7 bars - Weight: 3.7 ounces (105g) - Length: 7 7/8" (200mm) - Includes mounting hardware to securely attach to water bottle bosses or under bottle cage
    Ortlieb Ultra Light Bicycle Mirror
    $29.95
    This Ultra Light Bike Mirror is designed for commuting, touring or just about anytime you need to increase your line of vision. -Weighs only 2 oz. -Unique clamp allows mounting on handlebars, bar-ends, fork blades. -Great for recumbents -Made in Germany -Imported by Ortleib
    Origin8 Light Mount - Eyelet Stub Silver
    $10.95
    Can be used to mount lights to any M5 threaded eyelet, rack mount or braze-on. - AL6061 alloy construction - 26mm diameter; 46mm length - M5 hex bolt included
    Nitto BM-R3 Rack for Brompton
    $180.00
    Dress up your Brompton with the BM-R3 rack made by Nitto specifically for Brompton. It is beautifully constructed of Cro-Moly tubing and nickel plated to a lovely soft finish Nitto calls "dull-bright". Stronger and better looking than the standard Brompton rack, it will serve you well and look stylish for the life of your Brompton. Bikes with racks ("R" version) are more stable when folded than those without racks and also roll better due to the larger support surface provided by 4 wheels rather than 3 on the rack-less versions. - For an "E" version bike (no fenders), the supplied hardware is all you need. - For an "L" version bike, longer bolts are required for mounting the rack stays at the same point as the existing fender stays. Put a note in the comment field at checkout and we will include 2 M5x20 stainless steel bolts for an extra $5. - For an "R" version bike the Nitto rack will simply replace the existing Brompton rack with the supplied hardware. NOTE: The BM-R3 rack has a single hole light/reflector mount. To mount a light or reflector with 50mm or 80mm on-center holes, you will need the B&M single hole adapter (see below). 1.55 lbs/703g
    NiteRider Mako 200
    $24.99
    NiteRider understand lights are an integral part of your daily commute. Using a light can mean the difference between being seen or not by automobile drivers. Many of the “entry level” commuter lights are nothing more than “be seen” lights. Your overall safety and visibility should not be limited by your budget, that's why NiteRider created the Mako Series. The Mako line offers three models and up to 250 lumens, not only allowing the cyclist to be seen, but allowing the cyclist to see as well. A favorite feature is the side “gills” that emits light, it not only looks cool, but makes the Makos more visible. The Mako line is easy on the wallet and easy to operate. Side lights Economical, high output light Super bright flash setting ideal for daylight use Easy operation battery operated (comes with 2 x AA) 3 light settings – High, Low and Flash Lumen Output: 200 Run Time: 15:00 – 60:00hrs Weight: 175g Battery: Alkaline AA x 2 WARRANTY The Mako 200 is backed by NiteRider's lifetime warranty that covers any defects in material and workmanship, mechanical components (housings, covers, mounts and fasteners) and LEDs. SYSTEM INCLUDES LED Light Head Handlebar Mount 2 AA Alkaline Batteries
    NiteRider Sabre 80
    $29.99
    The NiteRider Sabre 80 is a super bright, lightweight USB rechargeable LED tail light. It utilizes a multi LED array designed for eye catching visibility in both day and night. With the addition of amber colored side lights, the Sabre 80 provides 180 degrees of protection. Daylight Visible Flash (DVF) 80 lumen super bright tail light Easy on and off seat post strap mount with quick release tab Amber side lights for 180 degrees of visibility Convenient USB rechargeable Be Seen by cars = Be Safe FL1 Standard IP64, water resistant Lumen Output: 80 Run Time : 1:30 – 10:30hrs Charge Time: 1:30hrs Weight: 28g Battery: Li-Po WARRANTY The Sabre 80 is backed by NiteRider's lifetime warranty that covers any defects in material and workmanship, mechanical components (housings, covers, mounts and fasteners) and LEDs. SYSTEM INCLUDES LED Tail Light Seatpost Mount USB Cable
    NiteRider Solas 100
    $39.99
    The Solas 100 has two powerful LEDs, 4 modes (2 flash/2 steady) and is USB rechargeable. NiteRider implemented “Group Ride Mode” for cyclists who still want to stay visible and safe, but not distract others in the pack. - Daylight Visible Flash (DVF) - 100 lumen super bright tail light - Group Ride Mode – be seen without distracting fellow cyclists - Easy on and off seat post strap mount with quick release tab - Convenient USB rechargeable - Super bright daytime flash mode - Be Seen by cars = Be Safe - FL1 Standard IP64, water resistant